Matthew 6:10 Thy kingdom come, Thy will be done in earth, as it is in heaven.

Search
Close this search box.

Matthew 6:10 Thy kingdom come, Thy will be done in earth, as it is in heaven

How to Make a Tube Top From Scratch in 2024

how to make a tube top

If you’re concerned regarding how to make a tube top, there are a few different methods you can try. One approach is how to make a tube top from scratch using a pattern and fabric of your choice. Another option is to upcycle an existing t-shirt or tank top into a tube top by removing the sleeves and hemming the edges. Whichever method you choose, it’s important to take accurate measurements and follow the steps carefully to ensure a good fit and a professional-looking finished product. With a little patience and practice, you can create a cute and stylish tube top that’s perfect for summer weather or layering under jackets and cardigans. 

How to Make A Tube Top From Scratch 

bust measurement

1. To ensure that your tube top fits comfortably, it’s important to take accurate measurements of your bust and waist. After measuring these areas, add 1 inch (2.54 centimeters) to each measurement. This additional width will account for the necessary seam allowances when you begin to sew your tube top, allowing for a better fit and a more polished final product. 

how to make a tube top

2. To determine the appropriate length for your garment’s hems, measure from below your armpits to your waist, then add 2 inches (5.08 centimeters) to the measurement. 

3. Select your preferred fabric and lay it out in front of you with the wrong side facing up. For a tube top, it’s recommended to use a stretchy fabric such as jersey, which is commonly used in t-shirt production. 

4. Sketch a sizable rectangle based on your measurement, with the top of the rectangle corresponding to your bust measurement, and the bottom of the rectangle matching your waist measurement. The rectangle might slightly taper towards the bottom. 

5. Take the rectangle and fold it lengthwise, ensuring that the right sides are facing each other. Use sewing pins to secure the side edge, while leaving the top and bottom edges untouched for now. These edges will be hemmed at a later stage. 

seam allowance

6. Using a ½ inch (1.27 centimeters) seam allowance, sew along the side edge. As you sew, make sure to remove the pins to avoid any accidental pricks. Once you’re finished sewing, tie off the threads tightly with knots and snip them as closely to the fabric as possible. 

7. Using an iron, press the seam flat. Place the tube top on an ironing board, with the seam facing upwards. Spread the seam allowances apart and ensure they lie flat against the fabric on either side of the seam. Then, use a hot iron to press them flat. 

8. To create the hems, fold down the top and bottom of your fabric by 1 inch (2.54 centimeters). Use sewing pins to secure the folds in place, and then press them flat with an iron. At this point, the wrong sides of the fabric should still be facing outwards. 

9. Proceed to sew the top and bottom hems, leaving a ½ inch (1.27 centimeters) wide gap on the top hem. This gap will be used later to slide in the elastic. While sewing the hems, make an effort to sew as close to the raw/cut edge as possible, so that there’s enough room for the elastic. Once finished, remove the sewing pins, tie the ends of the threads tightly with knots, and cut them off as close to the fabric as possible. 

elastic measurement

10. Measure the circumference of your chest just below the armpits, and cut a piece of elastic to match that measurement. It’s important to use sturdy elastic, as it will help keep the tube top in place. 

11. Attach a safety pin to one end of the elastic. And use it to guide the elastic through the top hem. Locate the ½ inch (1.27 centimeter) wide gap on the top hem. Next, insert the safety pin into it, using it to thread the elastic through the hem. Once you reach the gap again, remove the safety pin. At this point, both ends of the elastic should be sticking out of the gap.  

12. Overlap the ends of the elastic by 1 inch (2.54 centimeters) and stitch them securely together. Use the smallest stitch possible, and be mindful not to sew through the fabric. Afterward, pull the elastic back through the gap. You can now sew the gap closed to achieve a cleaner finish. 

Bottom Line

So, now you know how to make a tube top from scratch in detail. If you want to make your custom tube top in bulk, Beautiful Connection Group is ready to give you affordable clothing manufacturing services. The Beautiful Connection Group, located in the United States, specializes in the production of women’s clothing. They offer a wide range of dress types, including tops, t-shirts, leggings, skirts, and more. This manufacturer is particularly advantageous for new clothing business owners since they do not impose high minimum purchase amounts; their minimum purchase amount is only 50. The company provides the flexibility to customize any dress design and choose any fabric. However, please check their website for more detail.